Hi there! Here is a new pen made from spalted tamarind wood, and a orion pen kit. It is a beautiful piece of wood and finishes well. The short piece is drilled with a 15/32 drill bit, the main body is drilled to a 25/64 size hole. After the tube is securely glued into each length of wood, the trimming of the ends, the different size bushings for each piece, the turning is the next step. Having sharp tools for the turning procedure is vital in the results. After the turning, sanding starting again with 400, 600, 1200, 1500, 2000, 4000, turning polish is then applied (several coats) and the bees wax, and we're ready to assemble the pen kit, and there you have it.

Hello! Here is another 30 caliber bullet pen this time made with bubingo wood. You will notice that the clip is in the form of a rifle with a scope, and the copper tipped bullet a look a like bullet. An ideal gift for a hunter.

Hello everyone. Here is another pen made from an acrylic blank and a mesa pen kit. The blank is approximately 5 inches long 3/4 x 3/4. If cut in half, two pens can be made with this (ocean mist) blank. Using sharp lathe chisels a process after drilling and trimminng the blank, taking very small cuts is the secret to making a very smooth finish. Once the blank is ready for the finishing segment I wet the surface with water on a cloth, (with the lathe running) and starting with 600 grit sandpaper, then wiping it clean with a soft cloth, and doing the same process with 1500, 2400, 4000, 8000, and finally 12,000 grit. I then use a finishing polishing called Mylands 3 step polishing system. This pen comes out a flawless beautiful pen, which uses a standard parker refill.

Here is my latest project of a laser inlay kit, made of black dyed spalted maple, cocobolo, and natural curly maple. The kit comes with 5 pieces (tube,4 pieces of wood) and assembly instructions. Since the laser has cut the openings for the rifle stock, barrel and the scope, it is required to insert the tube into the main body (curly maple) then pressing the the fitted pieces into there position. Then removing the tube form the body, and using CA thin glue (which dries almost immediately) onto the inserted parts and let dry.
Next try inserting the tube, however it may have been that some of the glue leaked through to the inner portion of the body. In that case taking a small dowel or pencil and wrapping a piece of 220 grit sand paper to smooth the inside until the tube can easily be placed in the body. Using a two part epoxy glue, coat the tube with the mix, be sure the tube is centered in the body, and let it dry over night. Sand both ends so that the tube and the body ends are flush. Turning this asssembly is critical and make sure the turning tools are sharp. Place on the lathe, I like to use 220 grit sand paper first to take the rough edges off the rifle parts if there are any slight protrusion. Then using the same procedure of finishing as in the previous posts, with 320, 400, 600,1200, 1500 grit, turners polish, and then the assembly is being done with a Mesa pen kit.

Another image of the finished antler pen

Hello everyone! Another manufactured pen made from deer antlers. I received the antlers from our pastor whose sport hobby is deer hunting. I cut one piece that was a bit of a triangle, which would be the pen holder, and drilled a hole at a 45 degree angle. Then I cut another piecefor the base for the pen, holding it in the vice to drill the centre for the 7 mm tube to be inserted. I drilled a curved piece of an antler for the top end of the pen. Next it was time to glue the tubes into the pieces and allowing overnight drying time, trimming all ends of the pen antlers, ready for the turning process.Turning the antlers was a very dusty procedure. Sanding was also a tough job as the finishing is slow and hard to get a real smoothfinish. Well that it for one more pen to add to my inventory.

This click pen is made of Bethlehem olivewood that comes from Israel. With each blank I receive is acompanyed with a " Certificate of Authenticity". The certificate states that the trees have been bearing fruits in the Nativity town of Bethlehem since the time of Jesus. It also states that it is an authentic Bethlehem Holy Land olive wood. The raw material that was produced from the pruning of the olive trees, the sprouts from the old and the unproductive trees which is an essential process for a heathier growth for the trees and to generate environmental stability.
No trees were damaged or destroyed in the process of harvesting this olive wood.